Go Back   Dodge Ram SRT-10 Forum - Viper Truck Club of America > Viper Truck SRT-10 Discussion > General Discussion
Home Forum Register FAQ Members List Social Groups Calendar Garage Mark Forums Read

General Discussion

Exhaust filling cab


This is a discussion on Exhaust filling cab within the General Discussion forums, part of the Viper Truck SRT-10 Discussion category!
Hey guys I have 05 srt10 regular cab been noticing exhaust filling my cab when defrost is on and sitting ...



Like Tree9Likes

Reply
 
LinkBack Thread Tools Display Modes
  #1 (permalink)  
Old 04-07-2018, 11:12 PM
Junior Member
 
Join Date: Feb 2017
Posts: 35
Member #16459
Exhaust filling cab

Hey guys I have 05 srt10 regular cab been noticing exhaust filling my cab when defrost is on and sitting at idle.... i have a jmb catch can and a roe crankcase breather and i can see fumes coming from the breather on drivers side and smells like fuel... i also have a tune from unleashed just noticed the smell a few months ago... was wondering if i could run a hose from my air intake to my catch can to help with vacuum right now its plugged off ? Any help or suggestions would be greatly appreciated thank you

Reply With Quote
  #2 (permalink)  
Old 04-07-2018, 11:55 PM
Member
 
Join Date: Apr 2017
Posts: 453
Member #16573
Most of us running a catch can, go from the valve cover to the can from the can to the cold air, that’s how it creates a vacuum
Jay212 likes this.
Reply With Quote
  #3 (permalink)  
Old 04-08-2018, 12:04 AM
Junior Member
 
Join Date: Feb 2017
Posts: 35
Member #16459
I was thinking same thing but the instructions with the jmb catch can say to plug the air filter off and the catch can has its own breather......should i remove the breather and run tube to my air intake? Thanks man!!
Reply With Quote
  #4 (permalink)  
Old 04-08-2018, 08:52 AM
rottenronnie's Avatar
VIPER POWERED
Canadian VTCoA Regional Member
 
Join Date: Jul 2006
Location: Calgary, Alberta
Posts: 2,440
Member #345
That's why I went to a closed Catch Can system (no air filter on top of the canister), so it didn't look like I had a 440 under the hood with bad valve cover gaskets. For the younger guys here that means smoke drifting between the fender and the hood.

Closed system= Zero smoke, Zero stink.
Psycho1122 likes this.
__________________
2005 QC N.A.
624 Wheel HP x 1.27 = 800-'ish flywheel (?)
Fully-Built 11:1 Pump-Gas
15.0 L/100 km. or 15.68 U.S. Miles Per Gallon
5600 pounds
[email protected] MPH in "D" for Drive

No Power Adders
Full B&B Exhaust with (4) Cats
Unported Street-Striker Heads w Custom Roller
Unported O.E.M. Intake Manifold
FSTJACK Hand-Ported TB
MONSTER R/X Dual-Vacuum Catch-Can
A fully-built 48RE transmission that actually keeps working!
Tuned by Maestro Chris Jensen

Last edited by rottenronnie; 04-08-2018 at 08:54 AM.
Reply With Quote
  #5 (permalink)  
Old 04-08-2018, 10:50 AM
VENOMOUS1 RACING's Avatar
Has Left the Room - Banned from VTCOA!
Southwest VTCoA Regional Member
Southwest VTCoA Regional Rep
2013 Viper Truck of The Month
 
Join Date: May 2009
Location: Wacko Waco,TX
Age: 44
Posts: 12,753
Member #10675
Remove catch can and be done! Raced them, build them, and have owned a few. Zero need for a catch can and I've put more miles than most here than most anyone. Overhyped and caused more issues than it relieved. They fill with condensation more so due to the install and location. My .02
Reply With Quote
  #6 (permalink)  
Old 04-08-2018, 12:10 PM
Junior Member
 
Join Date: Feb 2017
Posts: 35
Member #16459
If I remove the catch can should i close off the valve covers or run them back to stock? passenger side to air intake drivers side to intake manifold......the only reason I went with a catch can was to get rid of that burnt oil smell and to keep oil from seeping from my breather. Should I remove the breather too and put the cap back on? And yeah the only thing in the catch can was some rusty looking water.
Reply With Quote
  #7 (permalink)  
Old 04-08-2018, 12:18 PM
Junior Member
 
Join Date: Feb 2017
Posts: 35
Member #16459
The catch can isnt where the oil and steam is coming from it only has rusty water in it. The drivers side air breather is where the oil and fumes are coming from .Im afraid if I close it off completely it will only make more oil and fumes come out my breather.
Reply With Quote
  #8 (permalink)  
Old 04-08-2018, 12:25 PM
Almost Senior Member
 
Join Date: Jul 2006
Location: Stone Mtn, GA
Posts: 613
Member #373
Ive had the roe breather and catch can and got rid of both for the reasons you stated above OP. If I were to put on another catch can I'd go with a closed designed one.

Since im not stupid modified or anything I decided the stock configuration was good enough for me. I don't race my truck so it was no need for all of that stuff.
VENOMOUS1 RACING and Jay212 like this.
__________________
2005 Dodge Ram SRT-10 RC Bent Rod 5/2015 78K - Rebuilt by ARD Motorsports 8/2015 RIP 7/2018 112k
2005 Chrysler Crossfire SRT-6 *Daily Driver*
Reply With Quote
  #9 (permalink)  
Old 04-08-2018, 12:46 PM
Junior Member
 
Join Date: Feb 2017
Posts: 35
Member #16459
The reason I put the roe breather on was because my oil cap was constantly leaking oil I changed the cap with a aftermarket cap from autozone and it still leaked. Pissing me off having oil burning on my exhaust manifold
Reply With Quote
  #10 (permalink)  
Old 04-08-2018, 02:52 PM
Engin89's Avatar
Member
Northeast VTCoA Regional Member
 
Join Date: Jul 2012
Location: GA, Somewhere
Posts: 260
Member #13470
How many miles on this beast?
Sounds like hi manifold pressure. Tune running rich? CATS are know to fail maybe starting to restrict exhaust thus the smell........my 2 centa
__________________
06' Bril. Black R/C Born: 02:08:2006 10 AM, Build Number: 1058 of 1973, VTR-1762
Bitten:06/06/2012 Blood Type: 15-50W
Volant CAI, Full BBE bolt on, w/ hi-flo cats, Demon Coils, JTSVP TB, GenII Shifter, Oil Lines, 10mm Wires, 170 T, V1 UD Pulley, Dual Moroso catch cans, JMB Pipes & Stealth overflow.
Reply With Quote
Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Magnaflow exhaust for 06 quad cab and any other go fast bolt ons Privatetoe82 Wanted 5 07-10-2014 10:33 AM
Texas bunch Dyno #s and pics sim333 Dyno Stuff 71 10-23-2010 06:28 PM
SRT-10 SRT-Great General Discussion 22 06-14-2010 07:38 PM
Performance Power of Cylinder and Heads Bone General Discussion 10 04-09-2010 12:39 AM
Headers or Not??? SERPENT Performance Mods 62 02-13-2007 09:12 AM





All times are GMT -4. The time now is 09:36 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO
vB.Sponsors
This site is supported by its members, vendors, and administration. Vtcoa.com is in no way affiliated with Daimler Chrysler. Dodge, Viper,Ram SRT-10, the Viper logo and likeness are registered trademarks of Daimler Chrysler. The contents of this site are owned by Vtcoa.com and may not be used or reproduced without the express written permission of the Administrator.
GM Truck Forum
Ford Raptor Forums
Chevy Tahoe Forum
Chevy Cobalt Forum
Chevy Camaro Forum
Toyota FJ Cruiser Forum
Ford Truck Forum
88-98 GM Truck Forum
73-87 Gm Truck Forum
Ford Expedition Forum
Chevy Equinox Forum
Chevy Cruze Forum
Jeep Liberty Forum
Jeep Forum
Dodge Ram Forum
Chrysler 200 Forum
Scion xD Forum
Scion xB Forum
Dodge Challenger Forum
Sotball Forums
SRT Forum
Nissan Titan Forum
Buick Enclave Forum
Cadillac Forum
Cadillac XTS Forum