Go Back   Dodge Ram SRT-10 Forum - Viper Truck Club of America > Viper Truck SRT-10 Discussion > General Discussion
Home Forum Register FAQ Members List Social Groups Calendar Garage Mark Forums Read

General Discussion

Fan


This is a discussion on Fan within the General Discussion forums, part of the Viper Truck SRT-10 Discussion category!
Originally Posted by Bobby S The fan is after market Electric fan, not hydraulic original. You should have started off ...



Like Tree4Likes

Reply
 
LinkBack Thread Tools Display Modes
  #11 (permalink)  
Old 06-13-2018, 07:11 PM
Almost Senior Member
 
Join Date: Jul 2006
Location: Stone Mtn, GA
Posts: 613
Member #373
Quote:
Originally Posted by Bobby S View Post
The fan is after market Electric fan, not hydraulic original.
You should have started off with that information from the start. Alot of us dont change out the fan because the stock fan is plenty and is generally reliable.

Is there anything else done to your truck? Is it boosted?
rottenronnie likes this.

__________________
2005 Dodge Ram SRT-10 RC Bent Rod 5/2015 78K - Rebuilt by ARD Motorsports 8/2015 RIP 7/2018 112k
2005 Chrysler Crossfire SRT-6 *Daily Driver*
Reply With Quote
  #12 (permalink)  
Old 06-14-2018, 09:28 AM
Junior Member
 
Join Date: Sep 2012
Location: Old Bridge NJ
Posts: 41
Member #13618
Fan was changed by previous owner. Magnaflow exhaust, k&N air filter, pioneer sound system, back up camera. No other mods.
Reply With Quote
  #13 (permalink)  
Old 06-14-2018, 12:10 PM
trussman's Avatar
VIPER POWERED
Southeast VTCoA Regional Member
 
Join Date: Aug 2007
Location: Jacksonville, NC
Age: 36
Posts: 4,015
Member #2161
Send a message via Yahoo to trussman
Quote:
Originally Posted by earl lee View Post
You should have started off with that information from the start. Alot of us dont change out the fan because the stock fan is plenty and is generally reliable.

Is there anything else done to your truck? Is it boosted?
This^^^.
Stock hydraulic vs aftermarket electric isn't remotely the same.
__________________
Built by Royal purple. 501 hp/609 tq.
Reply With Quote
  #14 (permalink)  
Old 06-14-2018, 01:03 PM
Pirana131313's Avatar
Almost Senior Member
Midwest VTCoA Regional Member
 
Join Date: May 2012
Posts: 544
Member #13290
Quote:
Originally Posted by rottenronnie View Post
Hello: We have the same hydraulic-fan system that is used on the 2006 5.7L Hemis so there are a ton of them out there.
These are a balanced assembly that have to be replaced as an entire unit although they can (sort of) come apart.

Pick and choose from the information below.

Be Careful as THOSE FAN BLADES ARE SHARP!!!



http://driveviper.com/forums/threads...ing-in-traffic


HYDRAULIC FAN MOTOR DIAGNOSTIC PROCEDURES


DIAGNOSIS: This diagnostic procedure should be used if the engine overheats or the A/C compressor cycles rapidly. 1. Non-hydraulic system - Check for low coolant, faulty thermostat, faulty temperature sensor, etc. - Is there a Non-hydraulic system problem? a. Yes >> Repair as necessary. b. No >> Go to Step #2.
2. Power steering fluid - Check the power steering fluid level in the reservoir - Is the fluid in the power steering pump reservoir below the dipstick “Add” mark? a. Yes >> Check for leaks and repair as required. Fill the reservoir to the proper level and proceed to Step #3. b. No >> Go to Step #3. CAUTION: Fan blade and/or shroud may have sharp edges! 
3. Radiator cooling fan - Disconnect and isolate the negative battery cable from the battery. Rotate the fan counterclockwise (as viewed by the driver) using fingertips on the outer fan blade. Move the fan through 7 full rotations and notice the drag torque. - Does the fan spin freely through all 7 rotations with minimal finger exertion? a. Yes >> Go to Step #6. b. No >> Go to Step #4.
4. Does the torque needed to spin the fan significantly change as the fan is rotated? a. Yes >> Go to Step #18. b. No >> Go to Step #5
5. Is it difficult to turn the fan or does it require the effort of more than one finger? a. Yes >> Go to Step #18 b. No >> Go to Step #6
6. Testing the system - Connect the negative battery cable to the battery. Using the StarSCAN® perform the following tests with the engine running at idle speed. - Does the fan accelerate when given a 100% duty cycle command? a. Yes >> Go to Step #7. b. No >> Go to Step #12.
7. Does the fan decelerate when the duty cycle is changed from 100% to 0%? a. Yes >> Go to Step #8. b. No >> Go to Step #18.
8. At 0% duty cycle, turn the steering wheel to full left or right stop for up to 5 seconds (to stop fan rotation). - Does the fan rotate when the steering wheel is returned to center at 0% duty cycle? a. Yes >> Go to Step #9. b. No >> Go to Step #10.
9. Repeat Step #8, ten times. - Does the fan always resume rotation after the wheel is returned to center? a. Yes >> The hydraulic fan motor is OK. b. No >> Go to Step #10.
10. Turn the A/C system on. The ambient temperature or sun load must be high enough to cause the A/C compressor to cycle, this will normally be above 15.6° C / 60° F. With the A/C system operational, the fan speed should increase as the refrigerant pressure rises. If the A/C system does not operate because of low temperature (below 15.6° C / 60° F) or sun load, use the StarSCAN® to step the fan control motor solenoid duty cycle to 100%. - Does the fan always start soon after the A/C is turned “On” (or the duty cycle is set to 100%)? a. Yes >> Go to Step #11. b. No >> Go to Step #18.
11. Repeat Step #10, ten times stopping the fan between tests by turning the steering wheel. Does the fan speed always increase when A/C is turned “On” (100% duty cycle)? a. Yes >> The hydraulic motor is OK. b. No >> Go to Step #18.
12. Does pump noise increase indicating that the system pressure is increasing? a. Yes >> Go to Step #18. b. No >> Go to Step #13.
13. ELECTRICAL TESTING - Disconnect the 3 pin connector of the fan motor assembly jumper harness from the vehicle engine compartment wiring harness. Using the connector of the jumper harness for electrical measurements will normally allow easier access than if the connector at the hydraulic motor pressure control valve is used. Measure the resistance between terminal 1 and terminal 2 of the fan motor assembly jumper harness to determine fan motor solenoid resistance. (Fig. 3) - Is the resistance between 7 and 13 ohms? a. Yes >> Go to Step #14. b. No >> Go to Step #17.
14. Fabricate a 3 wire jumper harness between the vehicle engine compartment wiring harness and the fan motor assembly jumper harness connector. Insert an ammeter in the K173 BR/VT circuit (Fig. 3). Start the engine and set the duty cycle to 100%. - Is the current draw on circuit K173, BR/VT, between 0.5 and 1.5 amps? a. Yes >> Go to Step #17. b. No >> Go to Step #15.
15. Inspect for shorted or broken wires. - Were any wires shorted or broken? a. Yes >> Repair as necessary. b. No >> Go to Step #16.
16. Replace the Front Control Module (FCM).
17. Replace the fan control motor solenoid and retest the hydraulic fan motor.
18. Replace the hydraulic fan/motor/shroud assembly.

DIAGNOSTIC PROCEDURES:
Try the Fan-Spinning Test Above: Numbers 3, 4 & 5. This test seems conclusive and if mine passes, the most expensive replacement item is still functioning and an electronic control has malfunctioned.
If that isn’t the case, then the power steering pump may be weak. I don’t think that is true as it isn’t noisy and the steering is fine.
If the spin test fails, that leaves the purchase of a new Fan Module Assembly.
If the spin-test passes, make sure the electrical connector for the fan is hooked up and is in good (clean) condition. Then check the resistance of Pin 1 and Pin 2 of the connector as in Number 13 above. It may need to be replaced.
If the systems checked have passed thus far….
Disconnect the water temperature sensor during warm-up. At this time I can listen to the power steering pump as in #12 above.

This is what I did: (A Big Thanks to Dan Lesser)

Once the engine warmed up to about ¼ up on the gauge, I disconnected the coolant temperature sensor (which instantly pins the temperature gauge); and in about 2 seconds, the fan started roaring away at full-speed which meant much of the electrical and hydraulic fan systems were just fine.


More...http://www.wkjeeps.com/TSB/tsb_wk_0700205.pdf


Good Luck!

Ronnie


Awesome stuff!
__________________

AJ
'04
Full bolt on, 2/3 drop, 4:56's +lots of extras.


Boost Coming Soon.

Reply With Quote
  #15 (permalink)  
Old 06-14-2018, 06:06 PM
Almost Senior Member
 
Join Date: Jul 2006
Location: Stone Mtn, GA
Posts: 613
Member #373
Hopefully somebody with a e-fan setup can chime in, it sounds like some wiring issue with the fan or it might have burnt out?

OP, you'll be better off converting back to the mechanical fan setup if you want peace of mind since your not boosted or anything.
__________________
2005 Dodge Ram SRT-10 RC Bent Rod 5/2015 78K - Rebuilt by ARD Motorsports 8/2015 RIP 7/2018 112k
2005 Chrysler Crossfire SRT-6 *Daily Driver*
Reply With Quote
  #16 (permalink)  
Old 06-14-2018, 10:10 PM
noid's Avatar
Senior Member
 
Join Date: Nov 2006
Location: California
Posts: 1,026
Member #869
I think Justin has a plug and play wiring harness for a electric fan setup. I think he even has electric fans and shrouds. But it's been awhile since I looked into it.
__________________
05 silver QC with sunroof. side impact airbags.
NAvi with Sirius radio.

Mods: Permastar rims. billet center caps, Volant intake,Fastman Throttle body. Smaller crank pulley, Demon coils, SCT programmer, 2400 Stall Torque converter, Shift kit, Line lock, Jet hot coated Mopar headers, 3" exhaust, Magna flow, EBC rotors on all four, Amsoil, Cal Trac traction bars.

Mods waiting to be on: Aluminium one piece drive shaft, Drive shaft loop, Viper electric fan, braided brake lines & oil lines.
Reply With Quote
  #17 (permalink)  
Old 06-15-2018, 08:45 AM
Junior Member
 
Join Date: Sep 2012
Location: Old Bridge NJ
Posts: 41
Member #13618
Does anyone know of any knowledgeable SRT10 techs near Old Bridge NJ.
Reply With Quote
  #18 (permalink)  
Old 06-15-2018, 04:08 PM
Junior Member
 
Join Date: Sep 2012
Location: Old Bridge NJ
Posts: 41
Member #13618
Stopped by dealership for update. Now I am told Head gasket problem and engine issue. Quoted $13k repair "if" parts available thru dodge What the f--k!
Reply With Quote
  #19 (permalink)  
Old 06-15-2018, 04:42 PM
Slitherbeast's Avatar
VIPER POWERED
Canadian VTCoA Regional Member
 
Join Date: Sep 2007
Location: Alberta
Posts: 2,221
Member #2340
is there coolant in the oil? is the oil level higher than it should be with a milky color? are there bubbles in the coolant jug at idle or after a run? Does the coolant appear to be boiling in the coolant reservoir? Is it constantly low on coolant? Don't trust a dealership...... pull the spark plugs and see if you have any discolored and do a compression check. Dealerships sure are quick to provide a price without any real evidence....... my 2 cents.....
__________________
"Haters don't really hate you, they hate themselves cause you're a reflection of what they wish to be".


#993 04 blk RC 4.56 gears,Harland Sharp Rockers,3/8" Hardened Pushrods, PSI Valve Springs,,Striker Valve Cover Spacers, JMB catless mids,Magnaflow Catback, Torries' Tune,B&M Shifter,Stinker's Extreme Lowering Kit, Caltracs,Catchcan, Forged Wiseco Pistons,Molnar Rods, Clevite Bearings.Center Force Clutch,Cometics Head Gaskets,ARP Head Studs , Pioneer X950BH Double Din , Grants Steering Wheel , Bronze shifter bushing, Bronze pads, Billet Keys in the T56 . And the list continues......
Reply With Quote
  #20 (permalink)  
Old 06-15-2018, 09:55 PM
Almost Senior Member
 
Join Date: Apr 2015
Location: yelm WA
Posts: 563
Member #15071
Quote:
Originally Posted by Bobby S View Post
Stopped by dealership for update. Now I am told Head gasket problem and engine issue. Quoted $13k repair "if" parts available thru dodge What the f--k!
You could buy a whole used engine for half that
Reply With Quote
Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Cooling fan - A/C question 10-1=9 General Discussion 34 06-21-2014 11:52 PM
Fan Motor installation SANTEEN General Discussion 21 07-11-2011 08:35 AM
Engine cooling fan JTS VENOM PERFORMANCE Performance Mods 4 07-10-2006 03:18 PM





All times are GMT -4. The time now is 06:34 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO
vB.Sponsors
This site is supported by its members, vendors, and administration. Vtcoa.com is in no way affiliated with Daimler Chrysler. Dodge, Viper,Ram SRT-10, the Viper logo and likeness are registered trademarks of Daimler Chrysler. The contents of this site are owned by Vtcoa.com and may not be used or reproduced without the express written permission of the Administrator.
GM Truck Forum
Ford Raptor Forums
Chevy Tahoe Forum
Chevy Cobalt Forum
Chevy Camaro Forum
Toyota FJ Cruiser Forum
Ford Truck Forum
88-98 GM Truck Forum
73-87 Gm Truck Forum
Ford Expedition Forum
Chevy Equinox Forum
Chevy Cruze Forum
Jeep Liberty Forum
Jeep Forum
Dodge Ram Forum
Chrysler 200 Forum
Scion xD Forum
Scion xB Forum
Dodge Challenger Forum
Sotball Forums
SRT Forum
Nissan Titan Forum
Buick Enclave Forum
Cadillac Forum
Cadillac XTS Forum