Go Back   Dodge Ram SRT-10 Forum - Viper Truck Club of America > Members List
Home Forum Register FAQ Members List Social Groups Calendar Garage Mark Forums Read

SrtDub SrtDub is offline


Visitor Messages

Showing Visitor Messages 1 to 7 of 7
  1. SrtDub
    10-02-2013 06:04 PM - permalink
    ya h beam rods came in today, its a slow process but i am making progress. Justin at JMB says ill be lucky to make 650 whp with Paxton and that is kinda a little less than i am shooting for, he says procharger will do 750 with serpinite setup at 12psi. I haven't made up my mind yet tho or should i say made the money up yet lol. Either way i have to upgrade fuel pumps and injectors an get a tune on it so that 1600 bucks. And one plus on procharger kit is polished blower and powder coated brackets and not to mention the big nasty intercooler up front. As much money as i have in this build i am almost to the point of saying hey whats another 2500 dollars right... i think i have a drug addiction to horsepower
  2. LightningRaper
    10-02-2013 02:02 PM - permalink
    Sounds like it's going to be a fun winter, as bad ass as the procharger would be you got a good deal on a brand new Paxton I'd say try that out before you invest in procharger kit with a forged motor you should put up good #s you may want to up the Intercooler, you can sell the Paxton used for close to what you paid procharger kit is going to be around 10 when all said and done
  3. LightningRaper
    09-10-2013 12:03 AM - permalink
    any progress?
    03-14-2013 01:31 PM - permalink
    Making sure you aware of the huge Texas GTG this weekend in Temple, Tx. Meet and greet, racing, cruising and an all around great time. Look in the regional section for the Texas thread and get more info. Hope to see you there.
  5. LightningRaper
    02-26-2013 05:30 PM - permalink
    Damn that sucks, how much is the forging going to set you back? I just finished my Trans swap to 6 speed now I'm looking to build my bottom end
  6. SrtDub
    02-19-2013 02:12 PM - permalink
    two weeks after i bout that supercharger from you i spun a rod bearing so i got the engine out now doing a forged bottom end... This is getting pretty expensive lol but i am hoping to put 700 down to the tires
  7. LightningRaper
    02-08-2013 04:24 PM - permalink
    Hey, how's the truck coming along?

About Me

  • About SrtDub
    Engine Machinist
    2006 Qc SRT10
    Engine type and displacement
    8.3 V10
    Major modifications
    Single 88
    Tranny type
    Street Radials
    60 foot time
    1/8 Mile ET
    1/8 Mile MPH
    1/4 Mile ET
    1/4 Mile MPH
  • Signature
    Fully Built Motor (by me)
    Fully Built 48re (by me)
    88mm Garret Single Turbo Kit built (by me)
    Big thanks to JMB and JTSVP
    6200 Lbs [email protected] on Factory 22s


Total Posts
Visitor Messages
General Information
  • Last Activity: 09-04-2018 11:21 PM
  • Join Date: 11-07-2012
  • Referrals: 0


Showing Friends 1 to 2 of 2

My Viper Trucks

All times are GMT -4. The time now is 09:48 PM.

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO
This site is supported by its members, vendors, and administration. Vtcoa.com is in no way affiliated with Daimler Chrysler. Dodge, Viper,Ram SRT-10, the Viper logo and likeness are registered trademarks of Daimler Chrysler. The contents of this site are owned by Vtcoa.com and may not be used or reproduced without the express written permission of the Administrator.
GM Truck Forum
Ford Raptor Forums
Chevy Tahoe Forum
Chevy Cobalt Forum
Chevy Camaro Forum
Toyota FJ Cruiser Forum
Ford Truck Forum
88-98 GM Truck Forum
73-87 Gm Truck Forum
Ford Expedition Forum
Chevy Equinox Forum
Chevy Cruze Forum
Jeep Liberty Forum
Jeep Forum
Dodge Ram Forum
Chrysler 200 Forum
Scion xD Forum
Scion xB Forum
Dodge Challenger Forum
Sotball Forums
SRT Forum
Nissan Titan Forum
Buick Enclave Forum
Cadillac Forum
Cadillac XTS Forum