PVC?

Discussion in 'General Discussion' started by Thomas J, May 28, 2016.

Car Parts
  1. Thomas J

    Thomas J Full Access Member

    Messages:
    83
    Likes Received:
    0
    Joined:
    Nov 26, 2014
    Location:
    Beaufort, SC
    Is the hose coming from the drivers side valve cover the PVC?...Where does this hose run to? Had the intake off and now lost as to where it runs!:dontknow:
     
  2. Thomas J

    Thomas J Full Access Member

    Messages:
    83
    Likes Received:
    0
    Joined:
    Nov 26, 2014
    Location:
    Beaufort, SC
    PCV

    Getting there
     

    Attached Files:

  3. Thomas J

    Thomas J Full Access Member

    Messages:
    83
    Likes Received:
    0
    Joined:
    Nov 26, 2014
    Location:
    Beaufort, SC
    PVC

    :D Might even finish one day
     

    Attached Files:

  4. NVR2OLD

    NVR2OLD VTCoA Senior Member

    Messages:
    1,190
    Likes Received:
    2
    Joined:
    May 11, 2010
    Location:
    Rapid City, South Dakota
    Looking nice!:D
     
  5. VENOMOUS1 RACING

    VENOMOUS1 RACING Has Left the Room - Banned from VTCOA!

    Messages:
    12,751
    Likes Received:
    2
    Joined:
    May 15, 2009
    Location:
    Wacko Waco,TX
    Yes it's pcv. Should run under intake, connects to other side, then to bottom of intake.
     
  6. Thomas J

    Thomas J Full Access Member

    Messages:
    83
    Likes Received:
    0
    Joined:
    Nov 26, 2014
    Location:
    Beaufort, SC
    Damn...How far under intake?
     
  7. Thomas J

    Thomas J Full Access Member

    Messages:
    83
    Likes Received:
    0
    Joined:
    Nov 26, 2014
    Location:
    Beaufort, SC
    Can I attach w/o pulling intake?
     
  8. oldcolt

    oldcolt Striker Heads and Cam Supporting Member

    Messages:
    2,771
    Likes Received:
    161
    Joined:
    Jul 14, 2008
    Location:
    Calgary, AB
    Yes, it is in the center, just past the throttle body.
     
  9. VENOMOUS1 RACING

    VENOMOUS1 RACING Has Left the Room - Banned from VTCOA!

    Messages:
    12,751
    Likes Received:
    2
    Joined:
    May 15, 2009
    Location:
    Wacko Waco,TX
    Yes you can attach from underneath.
     
  10. earl lee

    earl lee Full Access Member

    Messages:
    613
    Likes Received:
    1
    Joined:
    Jul 12, 2006
    Location:
    Stone Mtn, GA
    Offtopic but does anybody know the hose diameter used on the JMB's oil catch can? Im moving mine to a different spot and need to pick up some hose.
     
  11. Thomas J

    Thomas J Full Access Member

    Messages:
    83
    Likes Received:
    0
    Joined:
    Nov 26, 2014
    Location:
    Beaufort, SC
    I think mine are 5/8"
     
  12. oldcolt

    oldcolt Striker Heads and Cam Supporting Member

    Messages:
    2,771
    Likes Received:
    161
    Joined:
    Jul 14, 2008
    Location:
    Calgary, AB
    I went out to the garage an measured my JMB catch can hose. It is 5/8" OD and 1/2" ID. It is very thin wall tubing. Go with the 1/2" ID and you should be good to go!
     
  13. earl lee

    earl lee Full Access Member

    Messages:
    613
    Likes Received:
    1
    Joined:
    Jul 12, 2006
    Location:
    Stone Mtn, GA
    Thanks guys.