BBK Throttle Body available NOW

Discussion in 'Cherry Performance' started by Cherry Performance, Jan 8, 2010.

  1. SANTEEN

    SANTEEN Active Member Supporting Member

    Messages:
    6,150
    Likes Received:
    0
    Joined:
    May 25, 2009
    Location:
    Miami, Fl
    Idle slightly low now?

    Put it on last night and drove it around the neighborhood, seem to run and idle fine. This morning after it warmed up, then idle seems a bit low, around 600 rpm. Even to the point where there is a slight hesitation when accelerating gradually from idle. Was there an idle relearn procedure that I should have done? I was assuming that the PCM would relearn the new throttle body after driving a bit.
     
  2. bclark05

    bclark05 New Member Supporting Member

    Messages:
    1,174
    Likes Received:
    0
    Joined:
    Dec 23, 2007
    Location:
    Hudson Falls,NY
    This might be the idle set screw I PM'ed you about, on the linkage.:dontknow:
     
  3. bclark05

    bclark05 New Member Supporting Member

    Messages:
    1,174
    Likes Received:
    0
    Joined:
    Dec 23, 2007
    Location:
    Hudson Falls,NY
    I just got off the phone with the old lady, and she said I can get one:rock: This is my valintines present:elefant: boy she loves me, she is the best:D
     
  4. SANTEEN

    SANTEEN Active Member Supporting Member

    Messages:
    6,150
    Likes Received:
    0
    Joined:
    May 25, 2009
    Location:
    Miami, Fl
    Supposedly, you shouldn't have to touch the idle set screw. The PCM should learn.
     
  5. Vman455

    Vman455 New Member Supporting Member

    Messages:
    438
    Likes Received:
    0
    Joined:
    Oct 27, 2009
    Location:
    Tacoma, WA
    Mine did--it was at 600rpm after I installed, but after a few days of driving around, it's back up to 750 at idle. You might just wait a bit and see what happens:dontknow:
     
  6. flchub

    flchub New Member Supporting Member

    Messages:
    2,384
    Likes Received:
    0
    Joined:
    Mar 12, 2007
    Location:
    west palm beach,fl
    you need a new engine,u threw a rod
     
  7. bclark05

    bclark05 New Member Supporting Member

    Messages:
    1,174
    Likes Received:
    0
    Joined:
    Dec 23, 2007
    Location:
    Hudson Falls,NY
    :p :p :p :p :p :p :p
     
  8. SANTEEN

    SANTEEN Active Member Supporting Member

    Messages:
    6,150
    Likes Received:
    0
    Joined:
    May 25, 2009
    Location:
    Miami, Fl
    Shut up BIT*h!!!!!!!!!!!!!!!!!!!!!!!!!!
     
  9. bclark05

    bclark05 New Member Supporting Member

    Messages:
    1,174
    Likes Received:
    0
    Joined:
    Dec 23, 2007
    Location:
    Hudson Falls,NY
    I will take one PM sent.:rock:
     
  10. Cherry Performance

    Cherry Performance Full Access Member

    Messages:
    379
    Likes Received:
    0
    Joined:
    Jan 13, 2009
    Sounds great:rock: :rock: Anyone else still want 1?
     
  11. 3m ta3

    3m ta3 New Member

    Messages:
    17
    Likes Received:
    0
    Joined:
    Oct 18, 2009
    Location:
    Southwest Ranches,FL
    Installed mine today,very noticeable difference in power.Money well spent.
     
  12. pirateman

    pirateman Full Access Member

    Messages:
    381
    Likes Received:
    0
    Joined:
    Feb 14, 2007
    Location:
    augusta ga
    what is the part number on the throttle body?
     
  13. Vman455

    Vman455 New Member Supporting Member

    Messages:
    438
    Likes Received:
    0
    Joined:
    Oct 27, 2009
    Location:
    Tacoma, WA
    Says #1776 on the box label.
     
  14. ZCx

    ZCx Active Member Supporting Member

    Messages:
    9,803
    Likes Received:
    19
    Joined:
    Sep 13, 2007
    Location:
    Big D
    mines comin in good:rock: :rock: :rock:

    for some weird reason i followed the directions & reset the ECM:aetsch: :aetsch: :aetsch: :aetsch:

    will have to tighten up the CalTracs:rock: :burnout: :rock: :burnout:
     
  15. SANTEEN

    SANTEEN Active Member Supporting Member

    Messages:
    6,150
    Likes Received:
    0
    Joined:
    May 25, 2009
    Location:
    Miami, Fl
    I rest the PCM following the procedures in this thread, post #7:
    http://www.vtcoa.com/forums/showthread.php?t=29794
    The idle is now spot on about 750 rpm. Howverer, I have a slightly sticking throttle. As I come to a stop the throttle will stick around 900 rpm at idle. If I just quickly blip the throttle, it goes right down to 750 rpm. I verified the sticking throttle by coming to a stop, putting the ebrake on, leaving it in gear, open the hood and I can actually pull the throttle linkage back about 1/32 of an inch and the idle will come right down to 750. Any ideas? Turn the idle set screw slightly in?
     
  16. Yellow venom

    Yellow venom Boosted Venom Supporting Member

    Messages:
    7,800
    Likes Received:
    0
    Joined:
    Jul 28, 2007
    Location:
    Edmonton,Alberta,Canada
    If you adjust the set screw ,the idle will hang,I tried it before,If you want to adjust the idle it needs to be done threw the computer,I've done mine with the SCT.That is what I have experienced with it.
     
  17. SANTEEN

    SANTEEN Active Member Supporting Member

    Messages:
    6,150
    Likes Received:
    0
    Joined:
    May 25, 2009
    Location:
    Miami, Fl
    It's not a matter of the PCM not setting the idle. The actually TB is sticking very slightly, right befor the throttle stop. I can actually pull it back about 1/32 of an inch and it idles perfectly. :dontknow: Other than that, I'm very happy with it.
     
  18. Cherry Performance

    Cherry Performance Full Access Member

    Messages:
    379
    Likes Received:
    0
    Joined:
    Jan 13, 2009
    Steven, I will call BBK Monday and let them know your problem and their solution.
     
  19. SANTEEN

    SANTEEN Active Member Supporting Member

    Messages:
    6,150
    Likes Received:
    0
    Joined:
    May 25, 2009
    Location:
    Miami, Fl
    Thanks. But dont get me wrong, other than that, I'm very happy with it.
     
  20. Cherry Performance

    Cherry Performance Full Access Member

    Messages:
    379
    Likes Received:
    0
    Joined:
    Jan 13, 2009
    I still want to find out if this is an ongoing problem or is this the only one. Has anyone else had a problem with the throttle body:dontknow: