Search results

Anybody know of a good transmission builder for our 10's? Starting to slip in 2nd now. Mine is a QC with the auto. It's got a lot of mods including the Paxton Novi. Dyno'd around 650RWHP recently, just wanted it built well enough to handle that. Don't plan on going any higher with it. I was...

My voltage went to crap on the 10 so I replaced the battery and ordered a new alternator (not easy to find and took a week to get it). When I started to disassemble everything to get to it (had to remove the Paxton brackets-that's a bitch!) I noticed my idler pulley is REALLY loose and my belt...

Ok guys, it's time for a performance rebuild for my trans. Who's the best, yet still won't break the bank, builder for the 48RE's near Greenville, SC? or should I go with replacement (Suncoast, ATS, Ramzilla, etc)? Opinions on what's the best route to go-I've got over 650rwhp.

Does anybody know of another 17"x10" other than the Eagle Alloy 058's that will fit our trucks without mods? :dontknow: I have the M&H's but the Eagles are on a nationwide backorder and won't be available for almost a month. I have an event in 2 weeks!!!!:( Please help!!

Anybody got a set of Caltracs for a 2005 SRT10 QC?

Hey guys, what's the best psi to run in the M&H's on our trucks (QC)?:dontknow: I'd like to hear form someone that's got them on a supercharged QC, if possible. What RPM are you launching at, especially on a concrete track? Any info would be great!

Anybody on here got an oil catch can they want to sell?

Anybody got a set of Eagle Alloy 058's 17"x10"' they want to sell or an equivalent wheel that fits our trucks without brake mods? I'm getting the M&H's from TNVIPER to go on them but I need the wheels for the event on March 14th.

Anyone interested in attending a closed track event for just 50 cars/trucks-Mopar only? It's on Saturday, March 14th from 9AM-5PM at ZMAX Dragway in Concord, NC. It's all late-model stuff-Challenger RT's and SRT8's, Charger RT's and SRT8's, Jeep SRT8's, and a couple of SRT10's. They have about 8...

Havin fun at the track!:D

Just in case any of you were wondering where to put your rear spoiler....BWAHAHAHAHAHA!:D

Anybody want to sell their current set up? I've got some cash and looking for a deal. Prefer drag radials and wheels that fit my truck without modifications.

Anybody want to sell their current setup? I've got some cash and I'm looking for a deal. Prefer drag radials and wheels that fit my truck without modifications.

Anyone going to the Vault Assault Street Racing Challenge this Thrsday, Dec 11th at the ZMAX Dragway in Concord, NC? Pre-register from 3-5pm. Racing from 5-9pm. I said I wasn't racing anymore until Spring buuuuut......sounds tempting!:D

I have my truck set up with higher shift points and higher rev limit. When I download the 93octane tune from the handheld it seems to fall flat for a split second when it shifts to second. It feels like it's barely bumping the rev limiter prior to the 1-2 shift. Any thoughts? Raise the rev...

Hey guys. Anybody had any problems with the coils on our trucks. My engine light came on and it felt like it was skipping a little so I ran a diagnostic with my handheld. It came up P0353 which is Ignition Coil #3 Primary Circuit. Does this mean I have to replace the coil or is it possible it...

Hey guys! I ran my new personal best today at SSHS8 @ Atlanta Dragway! (on the stock Pirelli's!) R/T .008 60' 1.888 1/8th 7.977 @ 89.55mph 1/4th 12.376 @ 112.81mph

We had a dyno day this past Saturday in Greenville, SC at JR Racing. For $40 bucks you got 2 pulls, lunch catered by Fudruckers, and a cool JR Racing tshirt. The highest hp winner got their session for free and the lowest hp got an hour of free shop time! The truck pulled highest hp of the...

Anybody on here going to SSHS8 at Atlanta Dragway? It's for 4,000lb+ cars/trucks only! I'll be there! :rock: Check it out at www.sshs8.com. It's this Satrday 11/8/08.

Anyone got a stock pair of 20" they want to sell?