Installing rear spoiler

[Greg Z]

OK damnit, I realize that I'm not mechanically incline but sheeesh, I can't seem to figure out how to install this spoiler and I even read the damn instructions LOL

I can't figure out how to mount these brackets to the truck (or spoiler?).

This is what I was given to do the install. Am I missing something?

The instructions seem to say that the brackets need to be bolted to the bed but there are no previous hole in the bed in the right area that I can find and the spoiler has OBVIOUSLY been bolted up to the truck because I can see the marks on the bed

bottom of spoiler

 

[kyle's srt10]

You need to take the tail lights out to install or uninstall the spoiler

 

[Ironhead]

i dont think you need them that is for if you were mounting wing on a truck other than a ten i dont have them on mine


EDIT,,,kyle is right they are in the tail light holes,i just went and looked at mine

 

[ZCx]

the top photo is to relocate the wing to the front of the bed if ya need to haul something.

where are the studs to mount the wing??????????
there are 2 bolts in the front of the wing foot & 2 studs that use nuts that go behind the tail lights

 

[Begood]

the top photo is to relocate the wing to the front of the bed if ya need to haul something.

where are the studs to mount the wing??????????
there are 2 bolts in the front of the wing foot & 2 studs that use nuts that go behind the tail lights

Correct, the 2 studs are missing. The studs need to be installed on the truck first (with the slot running front to back). To do this you must remove the tail lights, once the studs are installed you just slide the wing onto the studs then run the 2 bolts in from under the bed rail.


Bill.

 

[WOLFRAM]

WING INSTALL "101"

These are the "Blind bolts" used on the rear of the wing.

Remove the taillight screws.

Pull light off @ about a 45deg. angle.(So you don't break the snap studs)

Install the "blind bolts" in this hole. (Don't tighten yet)

Align "blind bolt" with the key hole on the wing.

Slide wing forward.

Install front two hex bolts, tighten all four. Reinstall lights.

For temporary removal. Remove front hex bolts & slide wing backwards & lift off.

To relocate to front of the bed. Attach the two brackets to the wing.

Turn wing backwards, attach to inside bed rail behind cab with the four remaining hex bolts.

P.S. The "Blind bolts" are the same ones used on the "DAYOTNA's".

 

[Greg Z]

Thnx WOLFRAM. I knew I had to me missing some hardware. Thnx again.

 

[ZCx]

i thought the studs were made into the wing.
learn something new every day

:rock: :rock: :rock:

 

[Outlawl]

hooray for Search engine!

The old owner of my 04RC contacted me and gave me the original wing for mine today! I am missing one of the rear stud bolts but other than that it is in pretty good shape.

 

[masari.jones]

I'm missing the front bolts on mine, anyone know what's the thread size of the front bolts/nuts?

Thanks...

 

[SRTVen]

Nice write up above.

 

[Thumperama]

OK damnit, I realize that I'm not mechanically incline but sheeesh, I can't seem to figure out how to install this spoiler and I even read the damn instructions LOL

I can't figure out how to mount these brackets to the truck (or spoiler?).

This is what I was given to do the install. Am I missing something?

Does Dodge even still sell the kit to mount the wing at the front of the bed?

I'd love to find one of these.

 

[Skypilot68]

 

[ZCx]

Does Dodge even still sell the kit to mount the wing at the front of the bed?

I'd love to find one of these.

scary, Google does not bring anything up by that part number:dontknow:

 

[briando]

i'm not a big fan of the spoilers anymore. i think the new line of dodge muscle cars looks awesome with the cleaner lines look