Rear end setup

[bigike]

Check this out yall!

Guys this looks like a 4-5 link to me!!!!!!!!!! on a STS 1000HP Viper truck!

 

[bigike]

http://www.truckshop.com/product.php?productid=20747&cat=332&page=1

And on that note why wouldn't the above set up work on our trucks. The axle tube is the same diameter as the v6 qc. The suspension is exactly the same in the rear with better shocks. Why won't this work.

 

[bigike]

Or this?

 

[yellowfever#154]

1st post looks more like a ladder bar setup, looking at the adjusting nut system on the lower link. Looks pretty trick, where did the picture from the 3rd post come from?

 

[JTS VENOM PERFORMANCE]

I dont know but the wiring looks like billy bob did it in the back yard

but I'm working on a ladder bar three link that will basically take the place of the leaf springs, use air bags, and ya choice of shocks, leave the fuel tank in place and the exhaust, and be a relatively easy install,
hope to have it done for the panama GTG

maybe along with tubular control arms

 

[WAZZSUP]

This guy is a member

This guy is a member here...recently. Said this setup was like......1500.00 or there abouts. I'll see if I can find the link....link...link, get it

Check this out yall!

Guys this looks like a 4-5 link to me!!!!!!!!!! on a STS 1000HP Viper truck!

 

[JTS VENOM PERFORMANCE]

Hey your right , thats msgnda or the tuner in fla:rock:


Wazzup is da man of remembrences

 

[Yellow venom]

http://www.truckshop.com/product.php?productid=20747&cat=332&page=1

And on that note why wouldn't the above set up work on our trucks. The axle tube is the same diameter as the v6 qc. The suspension is exactly the same in the rear with better shocks. Why won't this work.

This system isn't much different then the 4-link set-up with the coil overs on the 1st post,only real diff is switch the coil overs out for bags and the pan hard bar is on the bottom in post 1 and on top with the bags, I ran almost exactly the same air bag set up when I had my Dakota R/T show truck,it was an AirRide Technologies kit I used.Worked good ,NO wheel hop!:rock: :burnout:

 

[Yellow venom]

I dont know but the wiring looks like billy bob did it in the back yard

but I'm woring on a ladder bar three link that will basically take the place of the leaf springs, use air bags, and ya choice of shocks, leave the fuel tank in place and the exhaust, and be a relatively easy install,
hope to have it done for the panama GTG

maybe along with tubular control arms

Hey Stinker,Have you decided on what bags you will be using?Slam specialty bags?

 

[JTS VENOM PERFORMANCE]

Hey Stinker,Have you decided on what bags you will be using?Slam specialty bags?

My wife ..........she is a pretty big air bag

oh crap , I just said that out loud!LOLOLOL

 

[FSTJACK]

This is what the 4 link looks like on my Silver SRT-10

These pics were taken without the coilovers and before powder coating, and before the Mark Williams brakes, 40 spline axles ect.

 

[FSTJACK]

http://www.truckshop.com/product.php?productid=20747&cat=332&page=1

And on that note why wouldn't the above set up work on our trucks. The axle tube is the same diameter as the v6 qc. The suspension is exactly the same in the rear with better shocks. Why won't this work.

The axle tubes on the SRT-10 RCs & QCs are 3 1/2 " in diameter.
All other Dodge 1500 trucks are 3".


Quote:
Originally Posted by Yellow venom 366
This system isn't much different then the 4-link set-up with the coil overs on the 1st post,only real diff is switch the coil overs out for bags and the pan hard bar is on the bottom in post 1 and on top with the bags, I ran almost exactly the same air bag set up when I had my Dakota R/T show truck,it was an AirRide Technologies kit I used.Worked good ,NO wheel hop!



This picture was not a 4 link, it is/was a ladder bar set up......

 

[sleeper]

Jack, any idea when you'll get her done?

 

[bigike]

THAT IS MANY THOUSANDS OF DOLLAR WORTH OF WORK!

THE AXLE SADDLES ARE THE SAME SIZE FOR MY QC AS MY BUDDIES V6. MYBE THEY ONLY FIT DIFFERENTY IN THE POCKET OF THE SADDLE

TIME O BREAK OUT THE CALIPERS

 

[NBT]

This is what the 4 link looks like on my Silver SRT-10

These pics were taken without the coilovers and before powder coating, and before the Mark Williams brakes, 40 spline axles ect.

C'mon guy's/ Jack... when are you going to figure this out...that's not going to work at all... :dontknow: :hmmmm2: :stupid: :aetsch:
It's all ball bearing's these day's.:laugh:

 

[Floor]

wauw jack, big spender.... :adore: :top:

 

[nycstev]

http://www.truckshop.com/product.php?productid=20747&cat=332&page=1

And on that note why wouldn't the above set up work on our trucks. The axle tube is the same diameter as the v6 qc. The suspension is exactly the same in the rear with better shocks. Why won't this work.

Looks great.

 

[BIG NANA]

Stinker, You better put me down for one of your rear ladder bar or whatever setup you decide. I want one now!!

 

[JTS VENOM PERFORMANCE]

No prob bo, gonna start looking at it this weekend

oh wait , it is the weekend
gonna start lookin tommorrow, and try to order th parts next week

 

[msdnga]

You guys kill me, man, I snap picts just to show it long before I am done tidy'ing up.....:banghead:

SHeez...Stinker, there is a mans' head stickin out of your hoodscoop, tell them to move next time before you launch that monster...

It is a ladder bar system from ART.

I am changing my avatar to the following just so everyone can have a good laugh on me....