Rice Eater
Full Access Member
Can anyone point me to a place that lists all trouble codes? TX!
CEL Code #P-1486 ???
- Thread starter Rice Eater
- Start date
Rice Eater
Full Access Member
Roz-SRT said:
alright smart ass! thanks for the link!
"P1486-EVAP LEAK MONITOR PINCHED HOSE FOUND - SRT10"
Would this cause my truck to run rough cutting in and out sounds like its missing. I thought it was the TPS so I replaced that but still doing it and finally a light came on with the code. How can I trace the lines and look for a pinched hose:dontknow: Is it for the fuel?
RedSrt007
Active Member
its not a fuel hose, its a evap system hose (emmisions). There is a diagram somewhere (ill do a search for it on the forum) that has the route for the evap lines.
It starts @ the gas cap and works its way to the front of the motor. If your under warranty, best way is to have them deal with it and run tests with the drbIII.
-Red
It starts @ the gas cap and works its way to the front of the motor. If your under warranty, best way is to have them deal with it and run tests with the drbIII.
-Red
Rice Eater
Full Access Member
RedSrt007 said:
Chit.....no more warranty
Red do you think it could cause my cutting out condition?
ViperTruck2933
Full Access Member
How did you check for codes?
I tried turning my key on and off 3 times to see if I have any codes and I didn't see anything, anywhere.:dontknow:
Do the codes show up in the odometer section?
I tried turning my key on and off 3 times to see if I have any codes and I didn't see anything, anywhere.:dontknow:
Do the codes show up in the odometer section?
ViperTruck2933 said:
The very first time I tried it, I did the key trick, but I wasn't doing it fast enough. My first attempt was by turning it on/off three times and each time I returned to the off position I pressed the release for the key (M6,RC).
Then I did it by using one hand and holding down the key-release button and turning the switch on/off three times fairly quick and leaving the key in the on position on the third time, then the code displayed. I felt like a D.A.
The code is displayed in the odo section.
KRAZYSRT10
Full Access Member
- Joined
- Sep 2, 2006
- Messages
- 9,647
- Reaction score
- 0
ViperTruck2933 said:
I think there has to be something wrong with the system for something to actualy show up....but like ROZ said...turn you key 3 times in quick succession and on the third time leave it in the ON position.
Rice Eater
Full Access Member
do you have a CEL?
1qksrt
Full Access Member
- Joined
- Dec 16, 2006
- Messages
- 2,021
- Reaction score
- 0
Hey Chad
Call me,that code shouldn,t affect driveabilty!
Check all your basics first,PLUGS,Ign. wires and fuel.
When did the you first notice the problem?:dontknow:
You should have a missfire code(po301,302,ETC)
I can talk you through most of the diagnostics:rock:
Call me,that code shouldn,t affect driveabilty!
Check all your basics first,PLUGS,Ign. wires and fuel.
When did the you first notice the problem?:dontknow:
You should have a missfire code(po301,302,ETC)
I can talk you through most of the diagnostics:rock:
evap. leak, pinched hose.Rice Eater said:Chit.....no more warranty
Red do you think it could cause my cutting out condition?
J.R.
Rice Eater
Full Access Member
1qksrt said:
right on mickey....i'll give you a call when I get a chance to pull the plugs.:rock: thanks
Support Us
Become A Supporting Member Today!
