Search results

These are the smaller of the 2 m&h's that fit our trucks. These are a shorter than the 390's so the gearing is much lower (very noticable!) These work great for your standard bolt ons but probably too short for NOS or forced induction. Approx 50% tread left. $150 Plus shipping takes...

CORRECTION: This is a VEC II not a III...I posted in error and can't change the title of the thread. I bought this from a forum member as a VEC I. I sent it to ROE who did the VEC II update and sent me all the parts needed for the installation. I never ended up installing it cause I bought...

Selling my SCT Programmer. I got it from Marty at KRC perormance who made me a bad a$$ street tune and NOS tune on the dyno. The street tune I made 480 hp / 520 tq to the wheels with headers & exhust. The NOS tune pulled some timing and adjused fuel and made 600 hp / 760 tq on a 150 shot...

Sold my truck so selling the left over go fast parts. This mod was the best bang for the buck as far as HP/TQ gains. On a 150 shot with LT headers and catless mids it made 598 HP and 760 LBS of TQ to the WHEELS! Best 1/4 mile was 12.0 @ 116mph. Stock internals. This kit contains...

I thought this day would never come but work is getting very busy and I have a serious opportunity at my finger tips but need a 1-ton diesel dually for towing and can't swing both trucks even though mine is almost paid off. I am the 2nd owner and it has a clean car fax. 57,000 miles I put a...

Is there a tow hitch kit that I can buy online and install myself or should I take it to a shop and have them do it? How much should I expect to pay a shop for hitch & wiring harness for trailer lights?:dontknow: TIA

Boring parts but my passenger side front head lamp, turnsignal, rear break light and rear turnsignal do not work and its not the bulbs. All on passenger side. Also the AC has a mind of its own and blows cold when it wants to and doesn't when it doesn't want to. If you drive the truck around...

Hate to do it but we are getting a boat so I need a 3/4 ton diesel to tow it! SILVER 2004 Ram SRT-10 52,000 Miles gloss black powder coated rims X-metal Drop Cal Tracs X-metal Short Shifter w/ Rip Stick K&N Air Intake Mopar LT Headers w/ Catless Mids SCT Programmer Snug Lid EBC...

I see the forum has a new face lift....how do I search all active topics/recent posts in all forums at once like we used to?:dontknow:

Just looking for the Fronts...I already got the rears. Checking to see if any vendors here have them before I start gooleing:rock: Are rotors supposed to last more than 50,000 miles? I had the fronts turned once at about 25k i had to replace the backs when i bought it cause one was...

So my buddy let me borrow a brake/clutch bleeder kit. Anyone got any tips on how to do this?

I bought a new slave cylinder that mounts to the fire wall. Installed it and I had a pedal again and could easily shift between gears (w/ engine off.) connected the wire sensor and checked everything else. started it up and pulled out of garage...pulled forward 10 ft pushed clutch in and...

Wondering how they are...i want to smoothe out the ride a bit...alot of bumps and pot holes around here. I'm sure I'll loose some in the corners but do you think they are a lot softer than the 40's or just a little bit?

"I'll give youdetails on how I do it and so far it works well.. first fill the bottle with fluid, leave the cap off, put a small containor under the bleed screw to catch the fluid, and open the bleeder fully, let it drain out until the resevior is almost empty, fill and let it keep...

clutch has been fine still grips good. this morning i pulled out of the garage and pulled up to the first stop light and pushed the pedal in to go to neutral and it wouldn't go out of gear...i had to stand on the brake to stall it to stop the beast. I pumped the pedal a couple times and it...

Not sure what the compatability of the different years and QC vs RC are but I have an 04 RC w/410's and I want .456 or higher. I live in S. FL

390's w/ AE Alloy Wheels that I painted gun metal color. I have a few trips to the track with these and they have a little less than 50% tread remaining but still plenty of fun left to be had! Best of all they fit w/ out grinding the calipers. My best 60' was a low 1.8 but they really...

These are not the big dawgs but I have a pair of the 390's for sale w/ rims also. This size works great for a naturally aspirated / lightly modded truck. I have an 04 with .410's, headers, catless mids, K&N, caltracs. Because this tire is much shorter than the stockers the gear ratio is...

VEC III has all updates from ROE and includes an installation kit, stock tune card, 2 different performance tune cards and 5 new blank programable cards. Also has plexiglass cover for unit and all install and program instructions. $ 550.00 Shipped to USofA or Canadia History- I traded...

Just wanted to say whats up y'all...its been a while! I've styed in touch with a few but been about 6 months since I logged in. I haven't forgotten about you guys though:rock: Going to be posting up an updated VEC and 2 sets of rims w/ M&H drag radials for sale here pretty soon. So what...