Brand new in original box, discontinued 2006 SRT 10 center console bezel for automatic transmission, bought it for when I was going to do an auto swap but never did. Part number 1-1BZ84AAAAB has the carbon fiber design not the woodgrain.
SOLD
looking for info on these wheels they appear to be 20" and Im pretty sure I was told years ago they were manufactured by HRE. I thinking of getting a set with custom rear width similar to the staggered set Scott's working on
Was wondering approximately how much HP will be lost going from a manual to a built auto. I will dyno the truck again to verify when I'm done. My truck is around the 700rwhp mark.
Looking for auto conversion parts for an 06 let me know price. No trades
Transmission - may get local
Flexplate
Column and linkage
Brake pedal - may buy new
Center console piece - may buy new
No traction + a long winter coming I was thinking of a project I could do. I read a post awhile back about an awd conversion but there was no real info on the subject except it would cost to much and too much fabrication.
Ive been doing some research, I have an 06 and we had an 06 1500 4x4...
I contacted our wheel supplier today and he informed me ofna company that does custom steel wheels. I want to run the m and h 390-40r17
Will a 17 clear the caliper?
Should I go with a 17x10 or 17x12 (12 recommended)
What backspacing will clear the spring and not have the tire stick way...
I've been reading all weekend trying to get the exact info I'm looking for. The t56 has been fun but also a pain with clutch issues, and occasionally missing 3rd. I am Mopar through and through and I know that the 4L80E is a better transmission than the 48Re but I don't think I could live with a...
Was cleaning the garage and have some stuff for sale
- Jmb cold air intake for roe setup carbon fiber coated (starting to peel under boot not visable) with k&n filter and black 90 boot. $180+ shp obo
- rad hard pipe with ends and the good band clamps coated in carbon fiber $80+ shp
-...
I have a polished Whipple from roe, looking for a black Whipple or older lynshom. Was told I could not paint or powered coat mine without having issues. Mine has maybe 5000km on it.
I'm planning on repainting my truck paints getting old some rock chip and typical black swirls. Even though I hand wash my truck very carefully it's starting to show its age.
I'm looking for opinions on exterior paint options. My truck currently is brilliant black pearl. I could just reliant...
I have been having issues with starting my truck the proper 710 cam supercharger tune. Long cranking... Sometime when it's warmed up it would stall on deceleration and ping around 2500rpm under 1/2 gas with 7#s boost.
So I would load the old supercharger tune that runs 6-7#s and 42#injectors...
I'm looking for the mopar cold air intake shield the goes in place of the battery box and factory air box, Or a K&N one. I prefer the mopar one but will take what I can. If anyone has any other bits and pieces from any of these kit let me know ( don't need the filters )
Thanks
Anyone who has an accusump which kit should I use and which install kit. I was on there site and didn't see a complete package, I might have glanced over it if they are listed.
Also how and where does it tie into the block. If there is any other things to know I appreciate it.
I need to space out my a/c compressor from 1/4"-1/2" don't know the exact amount yet. The belt I have seems around that much to long and there isn't one any smaller.
I was thinking of getting some 1/4" aluminum flat bar and drill the holes in the middle. Also thought of some tubing.
I will...
I'm just going to install a Gen X shifter I bought from a member long tome ago and was wondering if there is suppose to be a spacer between the shifter and the transmission I have about a 1/4" gap between the two. Or is there suppose to be spring tension?
Engine shop had made a mistake cutting the keyway too far in the crank. They fixed it and said it's ok now, but I don't trust it. Anyone know a part number for a speedy sleeve? I'm going to check into this tomorrow. Also I need verification on the crank diameter where the seal rides to the...
I don't plan on going to the track either get bad times or break something so going to sell Brand new never installed on truck 390-40R17 on eagle 058 17x10 with lug nuts. Prefer local sale but can ship. Would like $700.00 can post pics but will be a little bit.
My daily driver black lifted quadcab 5.9 sport was hit a month ago and written off. So I bought another one same year except its a Manuel, not a sport and it's green.
I already put the 6" lift and 35s on put on most of the other parts off the old one. And have the sport bumpers and grill...
I've got a brand new set of main studs (from Tony) that my builder did not use on my engine. $275 shipped
Set of red used msd wires (2000km on them) I'm going to be using black Taylor wires $75 shipped
Set of 10 48lb/hr long style injectors for roe setup (2000km on them) $260 shipped.
I will...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.